A hemisphere of diameter 50 mm is resting on its curved surface centrally on the top face of a frustum of a rectangular pyramid base 80 mm x 60 mm and top 60 mm x 40 mm, height 55 mm. Draw the isometric projection of the combination....

From VTU CAED LAB TUTORIALS

A rectangular pyramid of base 40 mm x 25 mm and height 50 mm is placed centrally on top of a cylindrical slab of diameter 100 mm and thickness 30 mm. Draw the isometric projection of the combination....

From VTU CAED LAB TUTORIALS

A cone of base diameter 50 mm and height 40 mm is placed centrally on the top face of a square slab of side 80 mm and height 20 mm. Draw the isometric projection of the combination of solids....

From VTU CAED LAB TUTORIALS

A hemisphere of diameter 50 mm is centrally resting on top of a square prism of base side 60 mm and height 30 mm such that the curved surface of the hemisphere is touching the top face of the prism. Draw the isometric projections....

From VTU CAED LAB TUTORIALS

A sphere of 45 mm diameter rests centrally over a frustum of a cone of base diameter 60 mm top diameter 40 mm and height 60 mm. Draw its isometric projections....

From VTU CAED LAB TUTORIALS

A sphere of diameter 50 mm rests centrally on top of a cube of side 50 mm. Draw the isometric projection of the combination of solids....

From VTU CAED LAB TUTORIALS

Draw the development of the lateral surface of a truncated cone using Solid Edge software,, whose front view is as shown in the following figure....

From VTU CAED LAB TUTORIALS

A hexagonal pyramid of 30 mm base sides has a side parallel to VP. Draw the development of the lateral surfaces of the retained portions of the pyramid cut by two perpendicular planes shown by dark lines in the figure....

From VTU CAED LAB TUTORIALS

A hexagonal pyramid of sides 35 mm and altitude 65 mm is resting on HP on its base with two of its base sides perpendicular to VP. The pyramid is cut by a plane inclined at 30 degree to HP and perpendicular to VP and is intersecting the axis 30 mm above t...

From VTU CAED LAB TUTORIALS

Develop the lateral surface of the cylinder of 40 mm diameter and height 60 mm cut by two section planes as shown in figure....

From VTU CAED LAB TUTORIALS

Draw the development of the truncated portion of the lateral faces of a pentagonal prism of 20 mm side of base and 50 mm height standing vertically with one of its rectangular face parallel to VP and nearer to it so as to produce a one piece development. ...

From VTU CAED LAB TUTORIALS

A square prism 30 mm side of the base and height 50 mm is resting on its base on HP such that one of its vertical faces is inclined at 40 degree to VP. It is cut as shown in the following front view figure. Draw the development of the lateral surface of t...

From VTU CAED LAB TUTORIALS

A Tetrahedron of sides 40 mm is resting on one of its sides on HP. This side is parallel to VP and 40 mm away from it. It is tilted about the resting side such that the base containing this edge is inclined at 30 degree to HP. Draw the projections of the ...

From VTU CAED LAB TUTORIALS

A Hexahedron of 30 mm sides is resting on one of its corners on HP such that one of its solid diagonal is perpendicular to VP. Draw the projections of the solid....

From VTU CAED LAB TUTORIALS

A cube of 40 mm sides rests on HP on an edge which is inclined to VP at 30 degree. Draw the projections when the lateral square face containing the edge on which it rests makes an angle 50 degree with HP....

From VTU CAED LAB TUTORIALS

A tetrahedron of 55 mm sides rests on HP on one of its corners such that an edge containing the corner is inclined to HP at 50 degree and VP at 30 degree. Draw the projections....

From VTU CAED LAB TUTORIALS

A pentagonal prism 25 mm sides of base and 50 mm axis length is suspended freely from a corner of its base. Draw the projections of the prism when the axis appears to be inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

A cone of base diameter 40 mm and axis length 50 mm is resting on a point on the circumference of its base such that its apex is at 40 mm above the HP and its top view of the axis is inclined at 60 degree to VP. Draw the top and front views of the solid. ...

From VTU CAED LAB TUTORIALS

A circular lamina of 30 mm diameter rests on VP such that one of its diameters is inclined at 30 degree to VP and 45 degree to HP. Draw its top and front views in this position....

From VTU CAED LAB TUTORIALS

A circular lamina of 50 mm is standing with one of its points on the rim on HP and the lamina inclined at 45 degree to HP. The diameter at right angles to the diameter which is passing through the point on which the lamina rests is parallel to VP. Draw it...

From VTU CAED LAB TUTORIALS

A circular lamina inclined to the VP appears in the front view as an ellipse of major axis 30 mm and minor axis 15 mm. The major axis is parallel to both HP and VP. One end of the minor axis is in both HP and VP. Draw the projections of the lamina and det...

From VTU CAED LAB TUTORIALS

A hexagonal prism 25 mm sides of base and 50 mm axis length is suspended freely from a corner of its base. Draw the projections of the prism when the axis appears to be inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

A pentagonal prism 25 mm sides of base and 60 mm axis length rests on HP on one of its edges of the base. Draw the projections of the prism when the axis is inclined to HP at 40 degree and VP at 30 degree....

From VTU CAED LAB TUTORIALS

A square prism 35 mm sides of base and 65 mm axis length rests on HP on one of its edges of the base which is inclined to VP at 30 degree. Draw the projections of the prism when the axis is inclined to HP at 45 degree.....

From VTU CAED LAB TUTORIALS

A square pyramid 35 mm sides of base and 60 mm axis length is suspended freely from a corner of its base. Draw the projections of the pyramid when the axis appears to be inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

A hexagonal pyramid 25 mm sides of base and 50 mm axis length rests on HP on one of its slant edges. With the help of Solid Edge software draw the projections of the pyramid when the axis is inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

A hexagonal pyramid 25 mm sides of base and 50 mm axis length rests on HP on one of its slant edges. Draw the projections of the pyramid when the axis is inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

A hexagonal pyramid 25 mm sides of base and 50 mm axis length rests on one of its slant triangular faces. Draw the projections of the pyramid when the axis appears to be inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

A pentagonal pyramid 25mm side of base and 50mm axis length is suspended freely from a corner of its base. Draw the projections of the pyramid using Solid Edge when the axis appears to be inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

A hexagonal pyramid 25 mm sides of base and 50 mm axis length rests on HP on one of its edges of the base which is inclined to VP at 30 degree. Draw the projections of the pyramid using solid Edge when the axis is inclined to HP at 45 degree....

From VTU CAED LAB TUTORIALS

The video shows the projection of a pentagonal pyramid 25 mm sides of base and 50 mm axis length resting on HP on one of its corners of the base such that axis of the pyramid is inclined to HP at 40 degree and appears to be inclined to VP at 45 degree....

From VTU CAED LAB TUTORIALS

The video shows the projection of a pentagonal pyramid 25 mm sides of base and 50 mm axis length when it rests on HP on one of its corners of the base such that the two base edges containing the corner on which it rests make equal inclinations with HP and...

From VTU CAED LAB TUTORIALS

Projection of a square pyramid 35 mm sides of base and 60 mm axis length while it rests on HP on one of its corners of the base such that the two base edges containing the corner on which it rests make equal inclinations with HP.The projections of the pyr...

From VTU CAED LAB TUTORIALS

This video shows the projection of a square pyramid 40 mm sides of base and 65 mm axis length when it rests on HP on one of its edges of the base which is inclined to VP at 30 degree. The pyramids axis is inclined to HP at 45 degree. The projection is exp...

From VTU CAED LAB TUTORIALS

Projection of a pentagonal lamina having edges 25 mm which is placed on one of its corners on HP such that the perpendicular bisector of the edge passing through the corner on which the lamina rests is inclined at 30 degree to HP and 45 degree to VP. The ...

From VTU CAED LAB TUTORIALS

The tutorial explains the projection of a circular lamina of 50 mm diameter resting on HP such that one of its diameters is inclined at 30 degree to VP and 45 degree to HP. The step by step procedure is explained using Solid Edge software....

From VTU CAED LAB TUTORIALS

Projection of a hexagonal lamina of 30 mm sides having two of its edges parallel to both the vertical and horizontal planes and one of its edges is 10 mm from each of the planes of projection. The surface of the lamina is inclined at an angle of 60 degree...

From VTU CAED LAB TUTORIALS

The video shows the projection of a triangular lamina resting on HP on one of its sides with its surface making 45 degree to HP and one of its median inclined 40 degree to VP. The orthographic projection is explained step by step with the help of Solid Ed...

From VTU CAED LAB TUTORIALS

The tutorial shows how to draw the projection of a hexagonal lamina with a corner in VP using Solid Edge....

From VTU CAED LAB TUTORIALS

This video tutorial explain the projection of a pentagonal lamina resting on HP on its side using Solid Edge software....

From VTU CAED LAB TUTORIALS

This video shows the projection of a line using Solid Edge and determines its inclination with HP and VP....

From VTU CAED LAB TUTORIALS

This video shows the projection of a line inclined to both HP and VP using Solid Edge....

From VTU CAED LAB TUTORIALS

This tutorial shows how to use the command finder to locate the hidden commands in Solid Edge....

From VTU CAED LAB TUTORIALS

The tutorial show the orthographic projection of two points using Solid Edge software....

From VTU CAED LAB TUTORIALS

This tutorial shows how to change the dimension text and text in Solid Edge drawings....

From VTU CAED LAB TUTORIALS